Yaesu FT817 and Elecraft KX1
A quick overview of two of the low-powered (QRP) HF radios
vq9ke- Length: 6:15
- Views: 4812
- Tags: Yaesu FT817 Elecraft KX-1 KX1 817 Elecraft Yaesu QRP
-
PFR3, KX1, HB1A QRP Radios
Informal review and my personal observations of the Hendricks PFR3, Elecraft KX-1 and HB-1
Elecraft K1, K2, K3, and KX1 Casual Comparison
This is a casual comparison of the K3, K2, K1, and KX1 receivers. Please note that the KX1 has no internal speaker. It is connected to an inexpensive outboard amp and there is some distortion evident. Using a headset, the KX1 sounds far, far better than it does on this video!
- stanscoyote
- Length: 9:09
- Views: 6324
- Tags: Elecraft KX1 K3 K2 K1 cw qrp elecraft radio comparison
-
kx1 flycutting 6061
flycutting 6061 aluminium on a novakon nm070 (sieg kx1). 5000rpm at 1.8" = 2400sfm with a c2 carbide cutter. 15ipm feed, about 1.6" width of cut and .003" depth. the head is well trammed left to right(x), but seems to need some tweaking in the y. 2 paralell cuts side by side with about 1.25" apar...
KX1 CNC - Milling an aluminum bracket
Milling the first part of an aluminum bracket to hold a panel. The mill is a Sieg KX1 bought from Arc Euro Trade (www.arceurotrade.co.uk Had some initial problems with spindle speed and feed but after some experimentation it worked out ok, still some chatter here and there though. /Oakes
CNC Mill Sieg KX1 Mach
Demo of the runing machine
- thercmachine
- Length: 1:34
- Views: 26821
- Tags: CNC Mach3 Sieg KX1 RCM Machines Junglinster Luxembourg
-
Elecraft KX1 - CW QSO - DJ3AS de SQ5LNU/QRP on 40m (HD)
This is small presentation of my little Elecraft KX1. Part of my QSO with Hal DJ3AS in hard conditions on 40m. Sorry for not so good audio in this movie. I worked from the big and empty room and my KX1 was connected to my HiFi... 73's
kx1 cnc milling vise clamp in 1018 steel
milling a vise clamp down on a novakon nm-070 / sieg kx1. this is the 4th one on the block. the tool has gotton noisy, i think its becoming dull at this point, the finish is slighly worse than the previous ones. feeds rates in the slotting operation is 5ipm, the climb milling is 10ipm. the plungi...
DCS: Black Shark - Sieg KX1 CNC Milling simulator gauge
Milling a part for a simulator variometer. The mill is a Sieg KX1 bought from Arc Euro Trade (www.arceurotrade.co.uk More info here: forums.eagle.ru /Oakes
DCS: Black Shark - Sieg KX1 CNC Milling simulator gauge - part 2
Milling a part for a simulator variometer -part 2 The mill is a Sieg KX1 bought from Arc Euro Trade (www.arceurotrade.co.uk More info here: forums.eagle.ru /Oakes
Sieg KX1 CNC Mill LittleMachineShop.com Ebay Auction
Please see our Ebay auction from LittleMachineShop.com for details regarding this mill. Manufactured new this year, it was displayed and used at the National Hardware Show in Las Vegas May 2010. From there it was shipped to our warehouse in Pasadena, CA and now ready for auction. The purpose of t...
- photoboost
- Length: 1:32
- Views: 4741
- Tags: SIEG KX1 Mach CNC littlemachineshop.com Desktop CNC Desktop Mill Mach3
-
kx1 built-in paddle and speaker part1
- jj1izwdirtbikerider
- Length: 0:56
- Views: 2086
- Tags: DSCN2429
-
DCS: Black Shark - Sieg KX1 CNC Milling simulator gauge - part 3
Milling a part for a simulator variometer -part 3 The mill is a Sieg KX1 bought from Arc Euro Trade (www.arceurotrade.co.uk More info here: forums.eagle.ru /Oakes
- ka50oakes
- Length: 9:50
- Views: 1153
- Tags: DCS DCS:BS Black Shark CNC KX1 Variometer
-
kx1 cnc circle pocket test
this is a clean up pass of a circle pocket in hard maple with my novakon/sieg kx1 mill. basically a second run of the tool path in the same pocket. the first pass made for a poor video because it was covered in maple chips.
Page: 1 of 44
